ALNOR Ventilation Systems
Project – Wentyle
WENTYLE are an AutoCAD application assisting in design and calculations of ventilation systems.
It operates with the following programs:
It also contains a duct and fitting data base on BH-Res CLIMAVER disc, DOSPEL fan and accessories data base and Flakt Bovent ventilators catalogue.
It also allows convenient system building and easy introduction of changes. Automatic calculation of pressure drop in the system to be set up or in fragments thereof is also possible. The program operates in AutoCAD environment as a result of extensive consultations among Polish ventilation designers. It is being developed continuously.
WENTYLE 3.2 PL IC version of the program is available in section „Download Program” operates with BricsCAd and IntelliCAD, versions above 4.
In this version, WENTYLE have ALNOR duct, round and square fitting data bases, BH-Res, Dospel and Flakt Bovent catalogues and full drawing capabilities of 3.2 version – designing along the path, editing fittings, renumbering, proprietary component and automatic tabulation.
The program has been tested with BricsCAD6PL ( VectorSoft) and IntelliCAD6.2 (InterSoft).
NOTE The most recent LT-Extender (demo of 200 activations) is available at: www.vectorsoft.pl
The older version of LT - Extender for AC2000LT, 2002LT, 2004LT, downloaded from our website (demo of 200 activations www.lt-extender.com)
To install a full version, after exhausting 200 activation: buy the most recent LT-Extender (older versions are no longer available), install it and then install older version demo, this is our point – it acquires proprieties of the full version.
- AutoCAD from 2000 to 2007 and older AutoCADR14
- AutoCADLT from 2000LT to 2007LT+LT Extender
WENTYLE program is free of charge
WENTYLE assists in designing ventilation systems based on round section ducts and square section and oval section ducts and fittings made by ALNOR.It also contains a duct and fitting data base on BH-Res CLIMAVER disc, DOSPEL fan and accessories data base and Flakt Bovent ventilators catalogue.
It also allows convenient system building and easy introduction of changes. Automatic calculation of pressure drop in the system to be set up or in fragments thereof is also possible. The program operates in AutoCAD environment as a result of extensive consultations among Polish ventilation designers. It is being developed continuously.
Operation with BricsCAD/IntelliCAD
In general, we recommend BricsCAD program.WENTYLE 3.2 PL IC version of the program is available in section „Download Program” operates with BricsCAd and IntelliCAD, versions above 4.
In this version, WENTYLE have ALNOR duct, round and square fitting data bases, BH-Res, Dospel and Flakt Bovent catalogues and full drawing capabilities of 3.2 version – designing along the path, editing fittings, renumbering, proprietary component and automatic tabulation.
The program has been tested with BricsCAD6PL ( VectorSoft) and IntelliCAD6.2 (InterSoft).
Operation with particular AutoCAD
A list of AutoCAD versions, operating with WENTYLE program is shown below:- Full versions of AutoCAD from 2000 to 2007 and older AutoCAD14
- AutoCAD LT in version 2000LT, 2002LT, 2004LT, provided that LT-Extender, version dated 15.08.2005 has been installed
Download from our archives - AutoCAD LT, in 2005 LT, 2006 LT, 2007 LT versions, provided that most recent version of LT – Extender has been installed, www.lt-extender.com
NOTE The most recent LT-Extender (demo of 200 activations) is available at: www.vectorsoft.pl
The older version of LT - Extender for AC2000LT, 2002LT, 2004LT, downloaded from our website (demo of 200 activations www.lt-extender.com)
To install a full version, after exhausting 200 activation: buy the most recent LT-Extender (older versions are no longer available), install it and then install older version demo, this is our point – it acquires proprieties of the full version.
